HTA�吊式彈簧減震器安裝說�
HTA Hanging type Spring shock absorber Installation instructions
安裝前，�(qǐng)確認淞江集團吊式彈簧減震器的型號和規格是否正確�
Before installation,make sure the model and the specification are correct.
安裝�(shuō)�
Installation guide
所需工具：公制口�17mm（M10）�19mm（M12）�24mm（M16）開口扳手�
Required tools�17mm（M10）�19mm（M12）�24mm（M16）open wrenches.
先與安裝位置處依�(jù)施工�(guī)范預埋符合荷重要求的基礎螺栓。（如圖1�
Embed required foundation bolts according to the loading on the installation location.(Fig 1)
吊式彈簧減震器結�(gòu)圖：
Hanging type shock absorber?structure drawing�
外形尺寸表：
Outline dimension table:
| �(guī)� | A (mm) |
B (mm) |
C (mm) |
h1 (mm) |
h2 (mm) |
H (mm) |
BD (mm) |
| HTA-A | 37 | 50 | 25 | 7 | 45 | 80 | 8-10 |
| HTA-B | 40 | 60 | 28 | 7 | 65 | 110 | 10 |
| HTA-C | 70 | 90 | 40 | 25 | 90 | 150 | 12-14 |
| HTA-D/E | 86 | 120 | 50 | 20 | 130 | 200 | 12-16 |
安裝�(shuō)�
Installation guide
將彈簧減震器裝到�(yù)留安裝位置的螺栓上面，并將螺栓鎖緊。（如圖2�
Fit spring dampers on the bolts at the reserved mounting position and lock the bolts.(Fig 2)
將彈簧減震器與設備連接的絲牙條裝上。（如圖3�
Fit the spring shock absorber with the wire bar attached to the device.(Fig 3)
使用上下兩顆螺帽安裝與設備連接的固定處，以便調整，此時上部螺帽不需要鎖緊。（如圖4�
Use the upper and lower two nuts to install the attachment to the device so that the upper nut does not need to be locked.(Fig 4)
將設備安裝或配管安裝完成�
Complete the equipeent and piping engineering installation.
使用�(kāi)口扳手調整下部螺帽來�(diào)整設備水平及彈簧壓縮量。（如圖5�
Apply the open wrench to adjust lower nuts for the balance of the eqipment and the press amount for the spring.(Fig 5)
�(diào)整完成后將上下兩顆螺帽相�(duì)鎖緊，即可完成淞江集�(tuán)HTA吊式彈簧減震器的安裝�(diào)整。（如圖6�
Lock the upper and lower nuts after adjusting.(Fig 6)
安裝后請檢查彈簧下壓量，如彈簧壓到底，則表示荷重不足，沒有減震效果。應該更換較大荷重的彈簧減震器型�(hào)，并�(qǐng)于本公司�(yè)�(wù)人員�(lián)系�
After the adjustment,check the press amount of the spring.If it appears with insufficient loading,please replace with bigger loading by contacting our staff.
安裝�(shí) �(qǐng)注意安全�
Be cautious during the installation.
保養須知：每月要觀察固定螺栓是否有松動，保持彈簧減震器安裝�(shí)彈簧下壓撓度是否正常�
Maintenance checking points:remain M12 fixed bolt locked,balance of the base,installation of the isolator,and the deflection of the spring.
�1）安裝前，請確認淞江集團吊式彈簧減震器的型號和規格是否正確�
Fig 1）Before installation,make sure the model and the specification are correct.
�2）將彈簧減震器裝到預留安裝位置的螺栓上面，并將螺栓鎖緊�
Fig 2）Fit spring dampers on the bolts at the reserved mounting position and lock the bolts.
�3）將淞江集團吊式彈簧減震器與�(shè)備連接的絲牙條裝上�
Fig 3）Fit the spring shock absorber with the wire bar attached to the device.
�4）使用上下兩顆螺帽安裝與�(shè)備連接的固定處，以便調整，此時上部螺帽不需要鎖緊�
Fig 4）Use the upper and lower two nuts to install the attachment to the device so that the upper nut does not need to be locked.
�5）使用開口扳手調整下部螺帽來�(diào)整設備水平及彈簧壓縮量�
Fig 5）Apply the open wrench to adjust lower nuts for the balance of the eqipment and the press amount for the spring.
�6）調整完成后將上下兩顆螺帽相�(duì)鎖緊，即可完成淞江集�(tuán)HTA吊式彈簧減震器的安裝�(diào)整�
Fig 6）Lock the upper and lower nuts after adjusting.
�(diǎn)擊下載：
橡膠接頭-1.jpg)
橡膠伸縮接頭DN50-1.jpg)
雙球橡膠接頭-1.jpg)
體顯示器及系�(tǒng)�(xiàng)目橡膠接頭發�.jpg)
